Thinkcar S5 Auto OBD2 Scanner Code Reader SRS/ABS/Transmission Diagnostic Tool

Description

Store category
Sign Up Now !
You may also like
Thinkcar S5 Auto OBD2 Scanner Code Reader SRS/ABS/Transmission Diagnostic Tool
Product Description
Thinkscan Plus S5 Introduction
▼Thinkscan Plus S5 as the Highest-level FULL OBD II Diagnostic Device 4 Systems For DIY users supported include Engine /SRS/ABS/Transmission Test Body Control Module etc
▼Free Upgrade Online
▼Pay for one Car model software can enjoy Free Upgrade 1 year the full system ,Such as :ECU Coding/ Action Test and other Special Function Cost: .95/year (you can buy from ThinkCar Store directly)
THINKCAR Plus S5
Support 4
Sy
stem Free Diagnostic:
This car obd2 scanner is capable of reading and clearing trouble codes of
ENGINE/ABS/SRS/
Transmission
.
Free Engine system Diagnostic:
You can diagnose the engine system via ecu obd2 port, support all 10 OBDII test modes, such as live data, O2 sensor test, component test and more;read and clear the engine error codes, find out the exactly problem, repair it, and turn off the MIL engine light.
Free ABS system Diagnostic:
Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you.
Free SRS system Diagnostic:
safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status.
Free
Transmission
system Diagnostic:
if your car is slipping or difficult to shift. The system plays an important part in the overall performance of your car.
Complete OBD2 functions:
Reading Codes:
Show the detailed description of the Diagnostic Trouble Code (DTCs).
Erasing Codes & Reset:
Turns off Check Engine Light (MIL), clears codes and resets monitors.
Data Stream:
Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
I/M Readiness Status:
Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
Read Live Data Stream:
Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
View Freeze Frame Data:
Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
O2 Sensor Test:
Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
On-Board Monitor Test:
Retrieves and displays test results for emission-related powertrain components and systems.
Read Vehicle Information:
Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
Component Test:
Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
THINKSCAN PLUS S5 Features:
1.AUTO VIN.
2.2 in 1 Date in graph.
3. DTCs Look Up.
4.
Diag
nostic Report.
28 Maintenance Service（
Need to purchase additional
）
1. Oil Reset
.
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
2. Elec.Throttle Adaption
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.
3. Steering Angle Reset
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.
4. Battery Matching
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.
5. ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.
6. Break-pad Reset
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.
7. DPF Regeneration
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.
8. Gear Learning
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed.
9. IMMO Service
To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed.
10. Injector Coding
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
11. TPMS Reset
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged,andtire is replaced for the car with tire pressure monitoring function.
12. Suspension Matching
This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.
13. AFS Reset
This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture.
14. A/T Learning
This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality.
15. Sunroof Initialization
This function can set the sunroof lock off, closed when it rains,sliding / tilting sunroof memory function,temperature threshold outside the car etc.
16. EGR Adaption
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.
17. ODO Reset
a) ODo reset is to copy,write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance.
18. Airbag Reset
This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable,it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use.
19. Transport Mode
ln order to reduce power consumption, the following functions may be disabled,including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal.
20. A/F Reset
This function is applied to set or learn Air/Fuel ratio parameters.
21. Stop/Start Reset
This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware).
22. Nox Sensor Reset
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu.
23. AdBlue Reset (Diesel Engine Exhaust Gas Filter)
After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required.
24. Seat Calibration
This function is applied to match the seats with memory function that are replaced and repaired.
25. Coolant Bleeding
Use this function to activate the electronic water pump before venting the cooling system.
26. Tyre Reset
This function is used to set the size parameters of the modified or replaced tire.
27. Windows Calibration
This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window.
28. Language Change
This function is used to change the system language of the vehicle central control panel.
Thinkscan Plus S5 Supports Languages:
English, French, German, Spanish, Russian, Italian, Portuguese, Japanese
Support 5000+ Worldwide Vehicle Coverage
For AUDI , For BENZ , For BMW , For CHRYSLER , For CITROEN , For DACIA , For DAEWOO , For FIAT , For GM , For HOLDEN , For HONDA , For HYUNDAI , For JAGUAR , For JPISUZU , For KIA , For LANDROVER , For MAHINDRA , For MARUTI , For MAZDA , For MINI , For MITSUBISHI , For NISSAN , For OPEL , For PEUGEOT , For PORSCHE , For RENAULT , For SAAB , For SEAT , For SKODA , For SMART , For SPRINTER , For SUBARU , For SUZUKI , For TATA , For TOYOTA , For USAFORD , For VOLVO , For VW...Updating
Please contact customer service for specific details.
How to send diagnostic feedback？
How to Register/Update Thinkscan Plus S5？
1.Initial Use
2.Turn on the Machine
3.Language Setting
4.Connect WIFI
5.Choose Time Zone
6.User Agreement
7.Create an Account
8.Typing in Business Information
Product Parameters:
Display Screen ：5-Inch/TFT(IPS)
Connection :Wi-Fi/Bluetooth
RAM:1G
ROM:16G
Working Temperature : 32℉~122℉
Storage Temperature: -4℉~144℉
Packing include:
1*Thinkscan Plus S5 Host
1*USB Cable
1*Card Reader
1*Manual
1*Packing Box
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
1.We accept payment by PayPal only !
2.Payment should be completed Within 8 days after buyer places the order, or else an ebay Unpaid Case will be opened .
3.If you Can Not Pay in time or Don't Want to Buy this product any more , please Cancel the transaction Before the Unpaid Case is Opened.
Delivery details
1.All of the items will be shipped to buyer's EBAY address,please confirm your address on Ebay before you buy.
2.Your order will be usually shipped out the same or next business days once the payment is made and cleared, except on weekends and holidays.
3.Most of products are checked and tested carefully before shipment.Well Packed protects your items with suitable material so as to avoid damage during transit.
4. If your package delayed few days, due to any unexpected factor, please wait patiently. your kind understanding would be highly appreciated!
Terms of sales
1. We can not guarantee that you will be able to access every module or use every piece of cd/dvd software. Compatibility varies due to variations in the cars modlue or availabilty of year it released from original factory
2.It's the buyer's responsibility to complete clearance when parcel reached your Customs.
3.We are not responsible for buyers's local taxes, please consult local Customs for Tax Details.
About us
We are eager to be your professional parner of automobile diagnostic tool.
We support remote assistance by Teamviewer if you have any difficulty in software installation.
Contact us
1. We are committed to providing customers with the best products and services
，
Please do not hesitate to leave us your positive feedback if you are satisfaction with our products ,delivery or services .
2. If you have Any Questions, Please do not hesitate to Contact Us by email/ ebay message. We will reply you within 12 hours and do our best solve the problem with you
（
Except on Weekends and Holidays
）
.
3.Work time:GMT8 (9:00am-18:30 PM) ,Except for Saturday (9:00-11:00AM) .